|
Who's Online
There currently are 5867 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
ADJUSTMENTS
4-5. CDP MODE TEST & ADJUSTMENT METHOD
Definition of Mechanical Mode
No
1
MODE
STOP MODE
DEFINITION & STATUS
- Disc haven�t been inserted or disc have been ejected. When disc shall be transported into the unit Mechanism shall be fixed at this mode. - Loading device can insert disc thru the slot. - Floating device being locked. - Disc have been inserted thru the slot in front of unit. It is transient state between STOP mode and PLAY mode. - If disc should be inserted at the state of POWER ON, disc shall be loaded by a series of operation of specified device. - Disc shall be played. - Floating device being unlocked.
2
LOADING MODE
3
PLAY MODE - After disc have being clamped on the turn-table, disc shall be rotated.
4
EJECT MODE
- Disc is to be ejected at this mode. It is transient state between PLAY mode and STOP mode. - If disc should be mounted at the state of POWER ON and commanded by EJECT key, disc shall be ejected thru the slot by a series of operation of specified device.
Standard values / Play-ability test
No ITEMS SPECIFIED VALUES, CONDITIONS STANDARD VALUES RELIABILITY LIMITS
1 2 Loading Time Ejecting Time 7sec + 3sec < 5 sec < 17 sec < 15 sec From insertion up to make sound. (TCD-784) From track No.1 Between the EJECT command and the disc eject completion. (TCD-784) From out-most Track, Between the PLAY command of in-most Track and marking sound. Shall be measure when the center of Disc is correspond with the center of Roller. Shall be measure when the center of Disc is correspond with the center of Roller.
TEST CONDITIONS, REFERENCES
CONNEC TION Fig.6 Fig.6
3
Access Time
6sec + 3sec
< 15 sec
Fig.6
4
Disc Take-up Force
> 120g > 120g
> 90g During play in low temp. > 70g During play in low temp. > 130g
Fig.6
5
Disc
> 80g
Fig.6
6 7
Clamping Force Mechanical Noise
> 130g Loading
Fig.6 Fig.6
Eject -Test should be performed in no reverberation If anything is not < 75dB(A) error, shall not room at the noise level of less than 20dB(A). Play < 40dB(A) -Test should be performed at the 50cm in front defined. Access < 70dB(A) of the unit. -IHF-A MODE (RMS-FAST)(TCD-792D) 12
|
|
|
> |
|