|
Who's Online
There currently are 6023 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The Service Manual for the Kenwood KR-V55R provided by owner-manuals.com was as described/advertised. The contents provided the necessary information to effect a diagnosis of the unit. The schematics above all else was instrumental in tracing the the signal flow from component to component.
;
This manual was the factory original. Excellent value and contained all the details I needed. Easy dowwnload provided the information when I needed it.
;
Impeccable, document très complet. Perfect, i get all i need. All schematic are correct. Thanks
;
The manual is of better quality compared to other. I found it less expensive and therefore it it is the best buy cost vs quality.
;
I bought the service-manual of the sony ICB-1020(an old transmitter-receiver) at "www.Owners-Manual.com", I found the service-manual for a fairly cheap price(in comparison with other sellers). I filled in some questions, payed the order with Ideal, and within 24 hours I had my service manual. I was very happy:In no time I had my service-manual and everything, but literally everything was noted down in the manual; the electronic scheme, the parts list, etcetera.
A very practical, reference-document.
ALIGNMENT INSTRUCTIONS
3.The adjustment of SCREEN 3-1. Confirm the presetting IBRM data of EEPROM according to CRT. 3-2. Press the [S2] KEY of SVC Remocon, horizontal line will be displayed. 3-3. Adjust SCREEN V/R of FBT so that the horizontal line reach the cut-off point. 3-4 To be completed adjustment of screen. Press the [S2] key to escape screen adjustment mode. 4.The adjustment of FOCUS 4-1. Receive PAL RETMA PATTERN(signal of company:2CH., PAL-B). 4-2. Adjust the picture to best distinct picture of 350 Line by revolve Focus Volume. 5.The adjustment of WHITE BALANCE 5-1. NITSUKI Setting : Set Nitsuki to the Auto Mode , Reference to the B , and System to the PAL . 5-2. Setting the Normal Stats 5-2-1. Adjust Picture to Normal mode. 5-2-2. Adjust the Gain of Nitsuki to suitability by manual when condition is Normal. - Adjust the standard illumination take within limit bright of Nitsuki and luminosity of SET into acount. - Exhortative Standard illumination, : High 70Cd/ , LOW BEAM : about 15Cd/ 5-2-3. Press the [S8]key of SVC remocon to adjustment of Whit Balance. X=0.288, Y=0.301 5-2-4. Memorize in Nitsuki after Adjustment of White Balance. 5-3. Adjustment of White Balance 5-3-1.Receive Nitsuki signal. 5-3-2.Adjust Picture to Normal mode. 5-3-3.The Adjustment of High Beam : Adjust R-DRIVE and G-DRIVE to R,G,B BAR come to center. 5-3-4.The Adjustment of Low Beam : Adjust R-BIAS and G-BIAS to R,G,B BAR come to center. 5-3-5.Repeat 5-3-3 and 5-3-4 to R,G,B BAR come to within center 1. 6.The adjustment of GEOMETRY 6-1. Press the [S-6]key on the SVC remocon to call up the Geometry mode. And then, Geometry OSD will be displayed. 6-1-1. All adjustment is base on PAL(50Hz), but it can be base on NTSC(60Hz) in case of need. 6-2. The adjustment of VERTICAL CENTER 6-2-1.Receive PAL RETMA pattern(signal of company:PAL-B 2CH). 6-2-2.Press the PR up/down Keys( ) to select V CENTER. Adjust with Vol Up/Down ( ) keys so that the center mark of the CRT may be located on the horizontal line in the middle of the pattern. In case of no center mark, adjust with Vol Up/Down ( ) keys to obtain a vertically symmetrical pattern.
-7-
|
|
|
> |
|